Chat now with support
Chat with Support

One Identity Safeguard for Privileged Sessions 5.9.0 - Administration Guide

Preface Introduction The concepts of SPS The Welcome Wizard and the first login Basic settings User management and access control Managing SPS
Controlling SPS: reboot, shutdown Managing Safeguard for Privileged Sessions clusters Managing a high availability SPS cluster Upgrading SPS Managing the SPS license Accessing the SPS console Sealed mode Out-of-band management of SPS Managing the certificates used on SPS
General connection settings HTTP-specific settings ICA-specific settings RDP-specific settings SSH-specific settings Telnet-specific settings VMware Horizon View connections VNC-specific settings Indexing audit trails Using the Search (classic) interface Using the Search interface Searching session data on a central node in a cluster Advanced authentication and authorization techniques Reports The SPS RPC API The SPS REST API SPS scenarios Troubleshooting SPS Configuring external devices Using SCP with agent-forwarding Security checklist for configuring SPS Jumplists for in-product help Third-party contributions About us

Creating an alias IP address (Microsoft Windows)

Purpose:

This procedure describes how to assign an alias IP address to a network interface on Microsoft Windows platforms.

Steps:
  1. Navigate to Start menu > Settings > Network Connections.

  2. Double-click the Local Area Connection and then click Properties.

  3. Select the Internet Protocol (TCP/IP) component in the list and click Properties.

  4. To display the Advanced TCP/IP Settings window, click Advanced.

  5. Select the IP Settings tab and in the IP Addresses section, click Add.

  6. Into the IP Address field, enter 192.168.1.2. Into the Netmask field, enter 255.255.255.0.

    Caution:

    If your internal network uses the 192.168.1.0/24 IP range, the 192.168.1.1 and 192.168.1.2 addresses might already be in use. In this case, disconnect SPS from the network, and connect directly a computer to interface 1 (labelled 1 or EXT) using a standard cross-link cable.

  7. To complete the procedure, click Add.

Creating an alias IP address (Linux)

Purpose:

This procedure describes how to assign an alias IP address to a network interface on Linux platforms.

Steps:
  1. Start a terminal console (for example, gnome-terminal, konsole, xterm, and so on).

  2. Issue the following command as root:

    ifconfig <ethX>:0 192.168.1.2

    where <ethX> is the ID of the network interface of the client, usually eth0 or eth1.

  3. Issue the ifconfig command. The <ethX>:0 interface appears in the output, having inet addr:192.168.1.2.

  4. Issue the ping -c 3 192.168.1.1 command to verify that SPS is accessible. A similar result is displayed:

    user@computer:~$ ping -c 3 192.168.1.1
    PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
    64 bytes from 192.168.1.1: icmp-seq=1 ttl=63 time=0.357 ms
    64 bytes from 192.168.1.1: icmp-seq=2 ttl=63 time=0.306 ms
    64 bytes from 192.168.1.1: icmp-seq=3 ttl=63 time=0.314 ms
    
    --- 192.168.1.1 ping statistics ---
    3 packets transmitted, 3 received, 0% packet loss, time 2013ms
    rtt min/avg/max/mdev = 0.306/0.325/0.357/0.030 ms

Open the page https://192.168.1.1 from your browser and accept the certificate shown. The Welcome Wizard of SPS appears.

Modifying the IP address of SPS

Purpose:

To configure SPS to listen for connections on a custom IP address, complete the following steps.

Caution:

Use this procedure only before the initial configuration of SPS, that is, before completing the Welcome Wizard. For details on changing the IP address or other network settings of a configured SPS system, see Network settings.

If you change the IP address of SPS, make sure that you use this address as the Physical interface 1 \xe2\x80\x94 IP address in the Networking settings section of the Welcome Wizard (see Configuring interface 1).

Steps:
  1. Access SPS from the local console, and log in with username root and password default.

  2. In the Console Menu, select Shells > Core shell.

  3. Change the IP address of SPS:

    ifconfig eth0 <IP-address> netmask 255.255.255.0

    Replace <IP-address> with an IPv4 address suitable for your environment.

  4. Set the default gateway using the following command:

    route add default gw <IP-of-default-gateway>

    Replace <IP-of-default-gateway> with the IP address of the default gateway.

  5. Type exit, then select Logout from the Console Menu.

  1. Open the page https://<IP-address-you-set-for-SPS> from your browser and accept the certificate shown. The Welcome Wizard of SPS appears.

Accessing the Welcome Wizard from a non-standard interface

Purpose:

To complete the Welcome Wizard on an interface other than Physical interface 1, complete the following steps.

Caution:

Use this procedure only before the initial configuration of SPS, that is, before completing the Welcome Wizard. For details on changing the IP address or other network settings of a configured SPS system, see Network settings.

If you change the network configuration of SPS to complete the Welcome Wizard on a non-standard interface, DO NOT use the IP address you use to access the Welcome Wizard as the Physical interface 1 \xe2\x80\x94 IP address in the Networking settings section of the Welcome Wizard (see Configuring interface 1). Otherwise, you will not be able to access SPS after the Welcome Wizard is completed.

Steps:
  1. Access SPS from the local console, and log in with username root and password default.

  2. In the Console Menu, select Shells > Core shell.

  3. Change the IP address of SPS:

    ifconfig eth0 <IP-address> netmask 255.255.255.0

    Replace <IP-address> with an IPv4 address suitable for your environment.

  4. Set the default gateway using the following command:

    route add default gw <IP-of-default-gateway>

    Replace <IP-of-default-gateway> with the IP address of the default gateway.

  5. Type exit, then select Logout from the Console Menu.

  1. Open the page https://<IP-address-you-set-for-SPS> from your browser and accept the certificate shown. The Welcome Wizard of SPS appears.

Related Documents