Chat now with support
Chat mit Support

Privilege Manager for Unix 7.2.1 - Release Notes

System requirements

Before installing Privilege Manager for Unix 7.2.1, ensure that your system meets the following minimum hardware and software requirements.

NOTE: Beginning with version 7.2.1, Privilege Manager for Unix supports only Linux-based systems for Privilege Manager for Unix policy servers.

Table 4: Hardware and software requirements
Component Requirements
Operating systems

See Supported platforms to review a list of platforms that support Privilege Manager for Unix clients.

Disk space

80 MB of disk space for program binaries and manuals for each architecture.

Considerations:

  • At a minimum, you must have 80 MB of free disk space. The directories in which the binaries are installed must have sufficient disk space available on a local disk drive rather than a network drive. Before you install Privilege Manager for Unix, ensure that the partitions that will contain /opt/quest have sufficient space available.
  • Sufficient space for the keystroke logs, application logs, and event logs. The size of this space depends on the number of servers, the number of commands, and the number of policies configured.

  • The space can be on a network disk drive rather than a local drive.

  • The server hosting Privilege Manager for Unix must be a separate machine dedicated to running the pmmasterd daemon.
SSH software

You must install and configure SSH client and server software on all policy server hosts.

You must enable access to SSH as the root user on the policy server hosts during configuration of the policy servers. Both OpenSSH 4.3 (and later) and Tectia SSH 6.4 (and later) are supported.

Processor Policy Servers: 4 cores

RAM

Policy Servers: 8GB

Upgrade and compatibility

Privilege Manager for Unix supports a direct upgrade installation from version 6.0 and higher. The Privilege Manager for Unix software in this release is provided using platform-specific installation packages. For more information on upgrading, see the One Identity Privilege Manager for Unix Administration Guide.

One Identity recommends that:

  • You upgrade your policy server (Master) systems before agents, and that a policy server is run at the same or higher level than agents.
  • All policy server systems and agents are upgraded to the latest version to take advantage of all new features.

The upgrade process will create symbolic links to ensure that your existing paths function correctly.

Use of the Privilege Manager for Unix clients (pmrun and pmshells) with a policy server in Sudo policy mode is not supported.

Product licensing

Although licenses are allocated on a per-agent basis, you install licenses on Privilege Manager for Unix policy servers.

No special commands are required to register or license the clients with policy servers. Hosts using the Privilege Manager for Unix agents are automatically granted a license once a request is received on the Privilege Manager for Unix policy server by means of the pmrun command.

To install a license file

  1. Copy the .dlv license file to the policy server.
  2. To install the license, run:
    # /opt/quest/sbin/pmlicense -l <license_file>

    This command displays your currently installed license and the details of the new license to be installed.

  3. When it asks, "Would you like to install the new license (Y/N) [Y]?", press Enter, or type: Y
  4. If there are other policy servers configured in your policy server group, it forwards the license configuration to the other servers.

See the Privilege Manager for Unix Administration Guide for more information about the syntax and usage of the pmlicense command.

Upgrade and installation instructions

NOTE: Due to a change in the communication protocol, using 7.1 or later clients and servers with 7.0 clients and servers is not supported. One Identity recommends you upgrade all of your 7.0 installations to 7.1 or later versions. Installations of release 6.x are not affected and can still be used with 7.1.

Upgrade instructions

For information on upgrading Privilege Manager for Unix, see Upgrade Privilege Manager for Unix in Privilege Manager for Unix Administration Guide.

Upgrading your license

Depending on whether you are upgrading Privilege Manager for Unix from a version earlier than 7.0 or from version 7.x, handling your license is different.

  • Upgrading from a version 7.x: If you have purchased Privilege Manager for Unix version 7.x without owning an earlier version, you will receive a new license. In this case, you do not have to perform any extra steps and can proceed with the upgrade process.

  • Upgrading from a version earlier than 7.0: The product licensing changed with Privilege Manager for Unix version 7.0. If you are upgrading Privilege Manager for Unix from a version earlier than 7.0 to version 7.x, you must upgrade your license first.

    In this case, make sure that you have received you upgraded license before starting the upgrade process.

When client machines attempt to join to the policy server using the pmjoin or pmjoin_plugin command, if you do not have the proper license, the following error message is displayed:

*** Checking connection to policy server host <policy-server>           [FAIL]
- ERROR: policy server <policy-server> has no valid license (for QPM4U)
- ERROR: Unable to connect to any policy servers

To display a summary of the combined licenses configured on this host, enter the following command without any options

pmlicense

To install a license, enter the following command. For more information on license installation, see Installing licenses in Privilege Manager for Unix Administration Guide.

pmlicense -l <path-to-dlv-file>
  • If the license file is valid, the installer displays the following:

    The selected license file (<path-to-dlv-file>) contains a valid license
  • If the license file is not valid, the installer displays the following error:

    Error: This license file is not valid. Please contact Quest Licensing for a new license file.

You will receive the following message after the license is installed, depending the success of the installation:

  • If the license is successfully installed:

    ** Successfully installed new license
  • If the license install is failed:

    ** Error: Cannot configure new license from file <path-to-dlv-file>
Verwandte Dokumente

The document was helpful.

Bewertung auswählen

I easily found the information I needed.

Bewertung auswählen