The ewmm-parser() can be used to parse messages sent by another syslog-ng host using the enterprise-wide message model (EWMM) format. Available in version
parser parser_name {
ewmm-parser();
};The iptables parser can parse the log messages of the iptables command. Available in version
@version: 3.25
@include "scl.conf"
log {
source { system(); };
parser { iptables-parser(); };
destination { ... };
};The iptables-parser() is actually a reusable configuration snippet configured to parse iptables messages. For details on using or writing such configuration snippets, see Reusing configuration blocks. You can find the source of this configuration snippet on GitHub.
| Synopsis: | prefix() |
Description: Insert a prefix before the name part of the parsed name-value pairs to help further processing. For example:
To insert the my-parsed-data. prefix, use the prefix(my-parsed-data.) option.
To refer to a particular data that has a prefix, use the prefix in the name of the macro, for example, ${my-parsed-data.name}.
If you forward the parsed messages using the IETF-syslog protocol, you can insert all the parsed data into the SDATA part of the message using the prefix(.SDATA.my-parsed-data.) option.
Names starting with a dot (for example, .example) are reserved for use by syslog-ng OSE. If you use such a macro name as the name of a parsed value, it will attempt to replace the original value of the macro (note that only soft macros can be overwritten, see Hard versus soft macros for details). To avoid such problems, use a prefix when naming the parsed values, for example, prefix(my-parsed-data.)
Names starting with a dot (for example, .example) are reserved for use by syslog-ng OSE. If you use such a macro name as the name of a parsed value, it will attempt to replace the original value of the macro (note that only soft macros can be overwritten, see Hard versus soft macros for details). To avoid such problems, use a prefix when naming the parsed values, for example, prefix(my-parsed-data.)By default, iptables-parser() uses the iptables. prefix. To modify it, use the following format:
parser { iptables-parser(prefix("myprefix.")); };The Netskope parser can parse Netskope log messages. These messages do not completely comply with the syslog RFCs, making them difficult to parse. The netskope-parser() of syslog-ng OSE solves this problem, and can separate these log messages to name-value pairs. For details on using value-pairs in syslog-ng OSE see Structuring macros, metadata, and other value-pairs. The parser can parse messages in the following format:
<PRI>{JSON-formatted-log-message}
For example:
<134>{"count": 1, "supporting_data": {"data_values": ["x.x.x.x", "user@domain.com"], "data_type": "user"}, "organization_unit": "domain/domain/Domain Users/Enterprise Users", "severity_level": 2, "category": null, "timestamp": 1547421943, "_insertion_epoch_timestamp": 1547421943, "ccl": "unknown", "user": "user@domain.com", "audit_log_event": "Login Successful", "ur_normalized": "user@domain.com", "_id": "936289", "type": "admin_audit_logs", "appcategory": null}
If you find a message that the netskope-parser() cannot properly parse, open a GitHub issue so we can improve the parser.
The syslog-ng OSE application sets the ${PROGRAM} field to Netskope.
By default, the Netskope-specific fields are extracted into name-value pairs prefixed with .netskope. For example, the organization_unit in the previous message becomes ${.netskope.organization_unit}. You can change the prefix using the prefix option of the parser.
@version: 3.25
@include "scl.conf"
log {
source { network(flags(no-parse)); };
parser { netskope-parser(); };
destination { ... };
};Note that you have to disable message parsing in the source using the flags(no-parse) option for the parser to work.
The netskope-parser() is actually a reusable configuration snippet configured to parse Netskope messages. For details on using or writing such configuration snippets, see Reusing configuration blocks. You can find the source of this configuration snippet on GitHub.
| Synopsis: | prefix() |
Description: Insert a prefix before the name part of the parsed name-value pairs to help further processing. For example:
To insert the my-parsed-data. prefix, use the prefix(my-parsed-data.) option.
To refer to a particular data that has a prefix, use the prefix in the name of the macro, for example, ${my-parsed-data.name}.
If you forward the parsed messages using the IETF-syslog protocol, you can insert all the parsed data into the SDATA part of the message using the prefix(.SDATA.my-parsed-data.) option.
Names starting with a dot (for example, .example) are reserved for use by syslog-ng OSE. If you use such a macro name as the name of a parsed value, it will attempt to replace the original value of the macro (note that only soft macros can be overwritten, see Hard versus soft macros for details). To avoid such problems, use a prefix when naming the parsed values, for example, prefix(my-parsed-data.)
By default, netskope-parser() uses the netskope. prefix. To modify it, use the following format:
parser {
netskope-parser(prefix("myprefix."));
};The sudo parser can parse the log messages of the sudo command. Available in version
@version: 3.25
@include "scl.conf"
log {
source { system(); };
parser { sudo-parser(); };
destination { ... };
};The sudo-parser() is actually a reusable configuration snippet configured to parse sudo messages. For details on using or writing such configuration snippets, see Reusing configuration blocks. You can find the source of this configuration snippet on GitHub.
| Synopsis: | prefix() |
Description: Insert a prefix before the name part of the parsed name-value pairs to help further processing. For example:
To insert the my-parsed-data. prefix, use the prefix(my-parsed-data.) option.
To refer to a particular data that has a prefix, use the prefix in the name of the macro, for example, ${my-parsed-data.name}.
If you forward the parsed messages using the IETF-syslog protocol, you can insert all the parsed data into the SDATA part of the message using the prefix(.SDATA.my-parsed-data.) option.
Names starting with a dot (for example, .example) are reserved for use by syslog-ng OSE. If you use such a macro name as the name of a parsed value, it will attempt to replace the original value of the macro (note that only soft macros can be overwritten, see Hard versus soft macros for details). To avoid such problems, use a prefix when naming the parsed values, for example, prefix(my-parsed-data.)
Names starting with a dot (for example, .example) are reserved for use by syslog-ng OSE. If you use such a macro name as the name of a parsed value, it will attempt to replace the original value of the macro (note that only soft macros can be overwritten, see Hard versus soft macros for details). To avoid such problems, use a prefix when naming the parsed values, for example, prefix(my-parsed-data.)By default, sudo-parser() uses the sudo. prefix. To modify it, use the following format:
parser { sudo-parser(prefix("myprefix.")); };© 2024 One Identity LLC. ALL RIGHTS RESERVED. Terms of Use Privacy Cookie Preference Center