Chat now with support
Chat mit Support

Safeguard Authentication Services 5.0.7 - Administration Guide

Privileged Access Suite for Unix Introducing One Identity Safeguard Authentication Services Unix administration and configuration Identity management Migrating from NIS Managing access control Managing local file permissions Certificate Autoenrollment Integrating with other applications Managing Unix hosts with Group Policy
Safeguard Authentication Services Group Policy
Group Policy Concepts Unix policies One Identity policies
Display specifiers Troubleshooting Glossary

Unable to authenticate to Active Directory

If Safeguard Authentication Services can no longer authenticate with Active Directory, the following solutions may help you troubleshooting the issue.

Table 30: Troubleshooting authentication problems
Problem Solution
The host's computer object has been deleted. Recreate the computer object, then restart vasd.
The host keytab is deleted or becomes corrupt. Delete then recreate the computer object and restart vasd.

Unable to install or upgrade

The most common installation or upgrade failure is that the Unix host cannot read the Safeguard Authentication Services application configuration in Active Directory. Ensure that you have followed the instructions in the Configure Active Directory for Safeguard Authentication Services section of the Safeguard Authentication Services Installation Guide and that the configuration has been created successfully.

During an upgrade, you may see an error that Safeguard Authentication Services cannot upgrade because the application configuration cannot be located. If you previously joined to a specific domain controller, Safeguard Authentication Services disabled DNS SRV record lookups. This means that Safeguard Authentication Services cannot resolve other domains in the forest and may be unable to locate the application configuration. In this case, you must ensure that the domain controller you specified is a global catalog. Otherwise, you must create the Safeguard Authentication Services application configuration in the domain that you join or you must properly configure DNS to return SRV records and join normally, rather than specifying a domain controller when you join.

For more information, see the About Active Directory Configuration section in the Safeguard Authentication Services Installation Guide.

Unable to join the domain

If you are unable to join the domain, run the preflight utility to validate your environment.

For more information, see The Safeguard Authentication Services Pre-Installation Diagnostic Tool in the Safeguard Authentication Services Installation Guide .

Then, verify the following:

  • Check that the Active Directory account specified during join has rights to join the computer to the domain.
  • Check that the Unix host is able to properly resolve the domain name through DNS.

If you are joining to a specific domain controller you must ensure that Safeguard Authentication Services can locate and read the configuration information in Active Directory. You should do one of the following:

  • Make sure the domain controller you specify is a global catalog.
  • Create the Safeguard Authentication Services application configuration in the domain to which you are joining.

    For more information, see the About Active Directory Configuration section in the Safeguard Authentication Services Installation Guide.

  • Properly configure DNS to return srv-records and avoid joining to a specific domain controller.

Unable to log in

If you are unable to log in as an Active Directory user after installing, check the following:

  1. Log in as root on the Unix host.
  2. Check the status of the Safeguard Authentication Services subsystems. To do this, run the following command:
    vastool status

    Correct any errors reported by the status command, then try logging in again.

  3. Ensure the user exists locally and is allowed to log in. To check this, run the following command:
    vastool user checklogin <username> 

    The output displays whether the user is a known Active Directory user. If not, you may need to map the user to an Active Directory account or Unix-enable the Active Directory account. If the user is known, an access control rule may prevent them from logging in. The output of the command displays which access control rules are in effect for the user.

You may need to restart window managers such as gdm in order for the window manager to reload NSS modules. Until the window manager reloads the NSS configuration, you will be unable to log in with an Active Directory user. Other services such as cron may also be affected by NSS changes. If you are unsure which services need to be reloaded, reboot the system.

Note:

If you are configuring Safeguard Authentication Services on VMwareESX Server vSphere (ESX 4.0) the reason you can not log in may be related to access control issues. For more information, see Configuring access control on ESX 4..

Verwandte Dokumente

The document was helpful.

Bewertung auswählen

I easily found the information I needed.

Bewertung auswählen