One Identity Safeguard for Privileged Passwords allows you to enable or disable SPP services from the Global Services page.

By default, services are disabled for service accounts and for accounts and assets found as part of a discovery job. Service accounts can be modified to adhere to these schedules and discovered accounts can be activated when managed.

It is the responsibility of the Appliance Administrator to manage these settings.

  • Navigate to Global Services to see the settings listed below.
    • Appliance Administrators can click the Disable All button to disable all services (as long as at least one service is currently enabled). A dialog will appear asking for confirmation before disabling the services.
    • Click a toggle to change a setting: toggle on and toggle off.
    • Click Refresh to update the information on the page.
    Table 129: Global Services settings

    Setting

    Description

    Disable All

    Appliance Administrators can use this button to disable all services (as long as at least one service is currently enabled). A dialog will appear asking for confirmation before disabling the services. You will need to reenable each service individually.

    Requests

    Session Requests

    Session requests are enabled by default, indicating that authorized users can make session access requests. There is a limit of 1,000 sessions on a single access request.

    Click the Session Requests toggle to disable this service so sessions can not be requested.

    NOTE: When Session Requests is disabled, no new session access requests can be initiated. Depending on the access request policies that control the target asset/account, you will see a message informing you that the Session Request feature is not available.

    In addition, current session access requests cannot be launched. A message appears, informing you that Session Requests is not available. For example, you may see the following message: This feature is temporarily disabled. See your appliance administrator for details.

    Password Requests

    Password requests are enabled by default, indicating that authorized users can make password release requests

    Click the Password requests toggle to disable this service so passwords can not be requested.

    NOTE: Disabling the password request service will place any open requests on hold until this service is reenabled.

    SSH Key Requests

    SSH key requests are enabled by default, indicating that authorized users can make SSH key release requests

    Click the SSH Key requests toggle to disable this service so SSH keys can not be requested.

    NOTE: Disabling the SSH Key request service will place any open requests on hold until this service is reenabled.

    API Key Requests

    API key requests are enabled by default, indicating that authorized users can make API key release requests

    Click the API Key requests toggle to disable this service so API keys can not be requested.

    NOTE: Disabling the API Key request service will place any open requests on hold until this service is reenabled.

    Password Management

    Check Password Management

    Check password management is enabled by default, indicating that SPP automatically performs the password check task if the profile is scheduled, and allows you to manually check an account's password.

    Click the Check password management toggle to disable the password validation service.

    NOTE:SPP enables automatic password management services by default. Typically, you would only disable them during an organization-wide maintenance window.

    When disabling a password management service, SPP allows all currently running tasks to complete; however, no new tasks will be allowed to start.

    Change Password Management

    Change password management is enabled by default, indicating that SPP automatically performs the password change task if the profile is scheduled, and allows you to manually reset an account's password.

    Click the Change password management toggle to disable the password reset service.

    NOTE:SPP enables automatic password management services by default. Typically, you would only disable them during an organization-wide maintenance window.

    When disabling a password management service, SPP allows all currently running tasks to complete; however, no new tasks will be allowed to start.

    SSH Key Management

    Check SSH Key

    SSH key check is enabled by default, indicating that SSH key check is managed per the profile governing the partition's assigned assets and the assets' accounts.

    Click the Check SSH Key toggle to disable the check service.

    Change SSH Key

    SSH key change is enabled by default, indicating that SSH key change is managed per the profile governing the partition's assigned assets and the assets' accounts.

    Click the Change SSH Key toggle to disable the change service.

    API Key Management

    Check API Key

    API key check is enabled by default, indicating that API key check is managed per the profile governing the partition's assigned assets and the assets' accounts.

    Click the Check API Key toggle to disable the check service.

    Change API Key

    API key change is enabled by default, indicating that API key change is managed per the profile governing the partition's assigned assets and the assets' accounts.

    Click the Change API Key toggle to disable the change service.

    Discovery

    Asset Discovery

    Asset discovery is enabled by default, indicating that available Asset Discovery jobs find assets by searching directory assets, such as Active Directory, or by scanning network IP ranges. For more information, see Discovery.

    Account Discovery

    Account discovery is enabled by default, indicating that available Account Discovery jobs find accounts by searching directory assets such as Active Directory or by scanning local account databases on Windows and Unix assets (/etc/passwd) that are associated with the account discovery job. For more information, see Discovery.

    Service Discovery

    Service discovery is enabled by default, indicating that available Service Discovery jobs find Windows services that run as accounts managed by Safeguard. For more information, see Discovery..

    SSH Key Discovery

    SSH key discovery is enabled by default. With the toggle on, SSH keys in managed accounts are discovered. For more information, see SSH Key Discovery..

    Directory

    Directory Sync

    Directory sync is enabled by default, indicating that additions or deletions to directory assets are synchronized. You can set the number of minutes for synchronization. For more information, see Management tab (add asset).

    Audit Log Stream

    Audit Log Stream Service

    Use this to send SPP data to Safeguard for Privileged Sessions to audit the Safeguard privileged management software suite. The feature is disabled by default.

    To accept SPP data, the Safeguard for Privileged Sessions Appliance Administrator must turn on audit log syncing. For information, see the Safeguard for Privileged Sessions Administration Guide.

    SPP and Safeguard for Privileged Sessions must be linked to use this feature. For more information, see SPP and Safeguard for Privileged Sessions appliance link guidance.

    While the synchronization of SPP and Safeguard for Privileged Sessions is ongoing, Safeguard for Privileged Sessions is not guaranteed to have all of the audit data at any given point due to some latency.

    NOTE: This setting is also available under Security Policy Management > Settings. For more information, see Security Policy Settings.

    SCIM Provisioning

    SCIM Provisioning

    Use this toggle to enable or disable SCIM provisioning on the appliance. For more information, see Adding identity and authentication providers.

    Application to Application

    Application to Application

    Use this toggle to enable or disable the application to application connection behind a web application firewall via the TLS termination reverse proxy.

    The following configuration information is displayed and can be updated using the button:

    • TLS Termination Reverse Proxy Subnet (CIDR format): The subnet for the TLS termination reverse proxy.

    • Service Port: The service port used for connecting. By default this is port 443.

    R
    Table 130: Global Services settings
    Setting Description

    Disable All

    Appliance Administrators can use this button to disable all services (as long as at least one service is currently enabled). A dialog will appear asking for confirmation before disabling the services. You will need to reenable each service individually.