Accelerating provisioning and single object synchronization
To smooth out spikes in data traffic, handling of processes for provisioning and single object synchronization can be distributed over several Job servers. This will also accelerate these processes.
NOTE: You should not implement load balancing for provisioning or single object synchronization on a permanent basis. Parallel processing of objects might result in dependencies not being resolved because referenced objects from another Job server have not been completely processed.
Once load balancing is no longer required, ensure that the synchronization server runs the provisioning processes and single object synchronization.
To configure load balancing
-
Configure the server and declare it as a Job server in One Identity Manager.
All Job servers must access the same LDAP domain as the synchronization server for the respective base object.
-
In the Synchronization Editor, assign a custom server function to the base object.
This server function is used to identify all the Job servers being used for load balancing.
If there is no custom server function for the base object, create a new one.
For more information about editing base objects, see the One Identity Manager Target System Synchronization Reference Guide.
-
In the Manager, assign this server function to all the Job servers that will be processing provisioning and single object synchronization for the base object.
Only select those Job servers that have the same configuration as the base object's synchronization server.
Once all the processes have been handled, the synchronization server takes over provisioning and single object synchronization again.
To use the synchronization server without load balancing.
For more information about load balancing, see the One Identity Manager Target System Synchronization Reference Guide.
Detailed information about this topic
Running synchronization
Synchronization is started using scheduled process plans. It is possible to start synchronization manually in the Synchronization Editor. You can simulate synchronization beforehand to estimate synchronization results and discover errors in the synchronization configuration. If synchronization stopped unexpectedly, you must reset the start information to be able to restart synchronization.
If you want to specify the order in which target systems are synchronized, use the start up sequence to run synchronization. In a start up sequence, you can combine start up configurations from different synchronization projects and specify the order in which they are run. For more information about start up sequences, see the One Identity Manager Target System Synchronization Reference Guide.
Detailed information about this topic
Starting synchronization
When you set up the initial synchronization project using the Launchpad, a default schedule for regular synchronization is created and assigned. Activate this schedule to synchronize on a regular basis.
To synchronize on a regular basis
-
In the Synchronization Editor, open the synchronization project.
-
Select the Configuration > Start up configurations category.
-
Select a start up configuration in the document view and click Edit schedule.
-
Edit the schedule properties.
-
To enable the schedule, click Activate.
- Click OK.
You can also start synchronization manually if there is no active schedule.
To start initial synchronization manually
-
In the Synchronization Editor, open the synchronization project.
-
Select the Configuration > Start up configurations category.
-
Select a start up configuration in the document view and click Run.
- Confirm the security prompt with Yes.
IMPORTANT: As long as a synchronization process is running, you must not start another synchronization process for the same target system. This especially applies, if the same synchronization objects would be processed.
-
If another synchronization process is started with the same start up configuration, the process is stopped and is assigned Frozen status. An error message is written to the One Identity Manager Service log file.
-
Starting another synchronization process with different start up configuration that addresses same target system may lead to synchronization errors or loss of data. Specify One Identity Manager behavior in this case, in the start up configuration.
Displaying synchronization results
Synchronization results are summarized in the synchronization log. You can specify the extent of the synchronization log for each system connection individually. One Identity Manager provides several reports in which the synchronization results are organized under different criteria.
To display a synchronization log
-
In the Synchronization Editor, open the synchronization project.
-
Select the Logs category.
-
Click 
in the navigation view toolbar.
Logs for all completed synchronization runs are displayed in the navigation view.
-
Select a log by double-clicking it.
An analysis of the synchronization is shown as a report. You can save the report.
To display a provisioning log
-
In the Synchronization Editor, open the synchronization project.
-
Select the Logs category.
-
Click 
in the navigation view toolbar.
Logs for all completed provisioning processes are displayed in the navigation view.
-
Select a log by double-clicking it.
An analysis of the provisioning is shown as a report. You can save the report.
The log is marked in color in the navigation view. This mark shows you the status of the synchronization/provisioning.
TIP: The logs are also displayed in the Manager under the <target system> > synchronization log category.
Related topics
