サポートと今すぐチャット
サポートとのチャット

Identity Manager Data Governance Edition 9.2.1 - Deployment Guide

One Identity Manager Data Governance Edition Deployment Guide Data Governance Edition system requirements Install One Identity Manager Data Governance Edition Deploy Data Governance Edition components Post installation configuration Authentication using service accounts and managed domains Working with managed hosts and agents Upgrade Data Governance Edition Remove Data Governance Edition Troubleshooting NetApp managed host deployment EMC managed host deployment SharePoint Farm managed host deployment

Configuring CEE framework

Data Governance Edition 7.0.2 (and higher) requires the EMC Common Event Enabler (CEE) 7.1 (or higher) framework to collect resource activity from an EMC storage device. The Data Governance agent will register with EMC CEE as a VCAPS endpoint. EMC CEE must be installed on the same server as the Data Governance agent. If you are collecting resource activity from the EMC storage device, you can only specify one agent to manage the EMC host.

To configure CEE framework

  • Install the EMC CEE framework on one or more Windows servers.

Note: EMC CEE must be installed on the same server as the Data Governance agent.

Next steps:

Creating the cepp.conf file (Celerra or VNX devices)

You must create a configuration file (cepp.conf file) before using the CEPA auditing feature to monitor file system activity on EMC Celerra or VNX storage devices. The cepp.conf file contains the information needed to connect Data Movers to the Windows computers where the CEE software is installed. It also defines the type of file system events that Data Governance Edition can collect from the EMC device.

To create and configure cepp conf file

  1. Using an SSH client (such as Putty.exe), connect to Control Station using its IP and port (the default is 22).
  2. Login using administrative credentials. The default user name and password on a Celerra system are nasadmin/nasadmin.
  3. Copy or create the cepp.conf file.

    • To copy the current configuration file from the Data Mover, run the following command: server_file movername -get.cepp.conf cepp.conf

      Where: movername is the name of your Data Mover. The default name is server_2.

    • To create the configuration file, open the VI text editor (or other preferred text editor) by running the following command: vi cepp.conf
  4. Using the text editor, edit the cepp.conf file and ensure the following configuration parameters are in the file:

    pool name=poolname servers=server1|server2 postevents=event1|event2|...

    Where: poolname is the name assigned to the set of Windows servers where the Event Enabler software from EMC is installed.

    Where: server1|server2 is the fully-qualified domain name of the Windows computers hosting the Event Enabler (CEE) software from EMC. If you have more than one server, separate them with a vertical bar (|).

    Where: event1|event2|... are the EMC events to be collected during security scans and activity collection. When specifying multiple events, separate them with a vertical bar (|).

    Note: Do not register for pre-events or post-err-events in the cepp.conf. These events are ignored by the Data Governance agent and add undue load on the EMC device.

    The following table shows events (postevents=) that can be registered in the cepp.conf and their mapping to Data Governance events that can be collected during security scanning and activity tracking.

    EMC cepp.conf event

    Data Governance Edition event
    CreateFile|CreateDir Create
    DeleteFile|DeleteDir Delete
    RenameDir Rename
    SetAclFile|SetAclDir SecurityChange
    CloseModified Write
    CloseUnmodified Read

    NOTE: If you configure your EMC managed host to collect real-time security changes and apply them to scanned data, you must include the following events:

    ...postevents=CreateFile|CreateDir|DeleteFile|DeleteDir|RenameDir|SetAclFile|SetAclDir

    For performance reasons, you may want to filter out the events that are not required, such as CloseUnmodified which are the "Read" events.

  5. Save the file. (Press Escape then type :wq)

  6. Run the following commands in the SSH client to publish the file to the Data Mover and restart the CEPA facility:

    server_cepp movername -service -stop

    server_file movername -put cepp.conf cepp.conf

    server_cepp movername -service -start

    Where: movername is the name of your Data Mover. The default name is server_2.

  7. Verify the CEPA status by running the following command:

    server_cepp movername -service -status

  8. Verify the pool configuration by running the following command:

    server_cepp movername -pool -info

Enabling system configuration auditing (Isilon devices)

EMC Isilon devices do not use the cepp.conf file; however, you must enable configuration change auditing and protocol access auditing in order for Data Governance Edition to perform security scans and collect resource activity on the EMC storage device.

Note: On the Data Governance server and all agent servers, you must have a Trusted Root Certificate Authority certificate to validate the Isilon server's HTTP certificate.

To enable auditing (OneFS web interface)

  1. Connect to the OneFS web interface.

  2. Select Cluster Management.
  3. Select Auditing.
  4. In the Settings pane, select the following check boxes:

    • Enable Configuration Change Auditing
    • Enable Protocol Access Auditing
  5. In the Audited Zones pane, add the zones to be audited:

    • Click the Add Zones button to add a zone.
  6. In the Event Forwarding pane, enter the following information:

    • CEE Server URIs: Enter the uniform resource identifier (URI) for the Windows server hosting the Common Event Enabler (CEE) software.

      Use the following format: http://<FullyQualifiedDomainName>:<Port>/cee.

      For example: http://server.test.abc.com:12228/cee

      The default CEE HTTP port is 12228.

      Click the Add another input field to add additional CEE server URIs.

    • Storage Cluster Name: Enter the resolved name of the EMC Isilon cluster.

      Use the following format: <ClusterName>.<DomainName>.com

      For example: Cluster1.test.abc.com

  7. Click Save Changes.

SharePoint Farm managed host deployment

SharePoint farms are similar to remote managed hosts in that they require an associated service account, even though they are installed locally on a SharePoint server. In addition, you can configure the level of auditing you want to perform on SharePoint farms.

関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択