To edit database connection properties
- Select the Configuration > One Identity Manager connection category.
The sections General, , Connection parameters, and classes are displayed in the document view with the database connection properties.
- To edit general properties of the database connection, select the General view and click Setup....
To edit target system connection properties
- Select the Configuration > category.
The sections General, Scope, Connection parameters, and Schema classes are displayed in the document view with the target system connection properties.
- To edit general properties of the target system connection, select the General view and click Setup....
Detailed information about this topic
The following information about system connections is .
Table 56: System connection properties
| System connection |
Default display value for the system connection.
NOTE: If the connection parameters of the differ from the loaded schema, the schema's display name is also displayed. In this case, the schema must be updated before the can be used. |
| Setup... |
Opens a dialog box for editing the system connection's general properties and configuring the contents of the synchronization log. |
 Updating schemas |
Updates the schema.
The synchronization project is saved before the schema is updated. This allows the existing schema to be reloaded if an error occurs during update.
NOTE: The synchronization is deactivated if the schema of an activated synchronization project is updated. Reactivate the synchronization project to synchronize. |
 Shrink schema... |
All schema types of the respective schema, which cannot be used in the synchronization project, are deleted from it. You can select schema type to be retained even though they are not used. |
 Browse... |
Start the Target System Browser.
Use the target system browser to view the target system data/One Identity Manager database. You can add, change, and delete system objects. You can test virtual schema properties.
The variable set selected in the 's toolbar is used to connect to the target system. |
 Edit connection... |
Starts the system connection wizard.
The system connection wizard allows you to edit the connection parameters of the current system connection, for example, if the has changed.
NOTE: Certain connection parameters correspond with the loaded schema. If these connection parameters are changed, the schema must be updated in the synchronization project so that synchronization can be configured and run successfully. This is necessary, for example, if the connection to another One Identity Manager database is established that has a different schema to the connection database.
- Click Update schema before continuing to edit the synchronization project.
|
| Connection parameter |
Lists all connection parameters. You can define connection parameter values as variables in order to use one synchronization configuration for synchronizing different target systems. |
| |
Specifies whether a scope is defined. You can edit the scope. |
| Classes |
All schema classes are listed in groups of schema types. |
| |
This displays the target system schema with all its schema types and their properties.
The schema browser is only available in expert mode. |
Table 57: General properties of a system connection
| Schema |
Name of the schema. |
|
Display name |
Schema display name. |
| Connection is read-only |
If this option is set, the system connector only has read access to the target system. Write operations are not run, only logged. Changes to objects in the One Identity Manager database are not provisioned in the target system. |
| Retry count |
Number of attempts at establishing the connection. |
| Delay between retries |
Time delay between retry attempts. |
| Create synchronization log |
Specifies whether a synchronization log with detailed information about the synchronization object is created. |
| Data to log |
Data to be recorded in the synchronization log. |
Detailed information about this topic
All the information, tips, warnings, and errors that occur during are recorded in the synchronization log. You can configure the type of information to record separately for each system connection.
To configure the content of the synchronization log
-
Edit the system connection properties.
-
To configure the synchronization log for target system connection, select the Configuration > category in the .
- OR -
To configure the synchronization log for the database connection, select the Configuration > One Identity Manager connection category in the Synchronization Editor.
-
Select the General view and click Configure.
-
Select the Synchronization log view and set Create synchronization log.
-
Enable the data to be logged.
NOTE: Some content generates a particularly large volume of log data. The synchronization log should only contain data required for error analysis and other analyzes.
- Click OK.
Synchronization logs are stored for a fixed length of time.
To modify the retention period for synchronization logs
Detailed information about this topic
In the general scope, you can specify system objects to be handled by . This allows you to limit the number of objects to synchronize. If no general scope is defined, all objects in the are synchronized.
In the reference scope, you define which system objects are loaded for the reference resolution. If no reference scope is defined, the general scope is also used for the reference resolution.
TIP: If a general scope is defined, but you want all system objects of a target system type to be available, create an empty reference scope. To do this, simply enter the display name of the reference scope. This means that no scope is calculated in the reference resolution.
If the was creating using a default , a scope is defined. You may edit this scope. A scope is not define if the synchronization project was created without a project template.
NOTE: To avoid data inconsistencies, define the same scope in both of the connected systems.
Detailed information about this topic
Section of a connected system