Risk – Cost center (page description)
To open the Risk – Cost center page go to Responsibilities > My Responsibilities > Cost centers > select cost center > Risk.
On the Risk – Cost center page, you can:
The risk index is calculated from the sum of all attribute-based values and the maximum of all assignment-based values.
The following tables give you an overview of the different functions and content on the Risk – Cost center page.
Table 388: Columns
|
Risk index |
Shows which property/assignment affects the risk index. |
|
Risk |
|
|
Weighting/change value |
Shows, depending on the type of calculation, the value used to weigh the determined risk index in the overall calculation or the value used to alter the risk index respectively. |
History – Cost center (page description)
Open the History – Cost center page by navigating through Responsibilities > My Responsibilities > Cost centers > select cost center > History.
On the History – Cost center page, you can show all the cost center's changes (see My cost center history).
NOTE: Which changes are shown depends on your system's configuration.
The information is divided out on to three tabs:
-
Events: Shows all the events, which affect a cost center, either on a timeline or in a table (see Displaying my cost center history).
TIP: To navigate along the timeline, click in the pane and move the mouse left or right whilst holding down the left button.
To zoom in or out, turn the mouse wheel.
-
Status overview: Shows an overview of all assignments (see Displaying the status overview of my cost centers). It also shows you how long each change was valid for. Use the status overview to track when changes were made and by whom. This way, you not only see the initial and current status but you also see all the steps in between.
-
Status comparison: You can select a date and display all the changes made from then until now (see Comparing statuses of my cost centers). You can also show what the value of the property was at the selected point in time and what the value is now.
The following tables give you an overview of the different functions and content on the History – Cost center page.
Table 389: Controls
|
Events tab |
|
Filter by |
Use this function to filter the changes by a specific criteria. For example, you can just display changes from a certain user.
TIP: To remove the filter again, click  (Reset filter) next to the corresponding filter. |
|
Switch to table view |
Use this button to display the changes in table form. |
|
Switch to timeline view |
Use this button to display the changes as a timeline. |
|
Status comparison tab |
|
Time and date picker |
Select from which point on you want to see the changes. |
|
Display changed values only |
Deselect the check box if you also want to see properties that have not changed since they were created. |
Table 390: Controls in the details pane of a change
|
Compare |
Opens the Status comparison tab.
Use this button to show all the changes that were made from the selected point in time until now (see Comparing statuses of my cost centers). You can also show what the value of the property was at the selected point in time and what the value is now. |
Table 391: Columns
|
Events tab (table view) |
|
Change type |
Shows the type of change. |
|
Property |
Shows the name of the property that was changed. |
|
Display |
Shows the value that was changed. For example, the name of a department. |
|
Date |
Shows the date the change was made. |
|
User |
Shows the user that made the change. |
|
Status overview tab |
|
Display |
Shows the type of change. |
|
Property |
Shows the name of the property that was changed. |
|
Value |
Shows the value that was changed. For example, the name of a department. |
|
Run started |
Shows when the change was made. |
|
End |
Shows for how long the changed value applied or whether it is currently in use. |
|
Status comparison tab |
|
Modified |
Show whether the change took place or not. |
|
Change type |
Shows the type of change. |
|
Object type |
Show the type of object involved in the change. |
|
Property |
Show the name of the object that was changed. |
|
Historical value |
Shows the value before the change was made. |
|
Current value |
Shows the value that is currently in use. |
TIP: You can show less data by using the column filters. For more information, see Filtering.
Usage – Cost center (page description)
To open the Usage – Cost center page go to Responsibilities > My Responsibilities > Cost centers > select cost center > Usage.
On the Usage – Cost center page, you can see the roles and organizations that belong to the identities to which this cost center is assigned (see Displaying role memberships of my cost center members).
The information is displayed as a hierarchical chart, which shows you more about the role inheritance.
The following tables give you an overview of the various features on the Usage – Cost center page.
Compliance reports – Cost center (page description)
