立即与支持人员聊天
与支持团队交流

Active Roles 7.5.3 - User Guide

Introduction Getting Started One Identity Starling Two-factor Authentication for Active Roles User or Service Account Management Group Management Computer Account Management Organizational Unit Management Management of Contacts Management of Exchange Recipients

Steps for creating a user mailbox

This section provides instructions on how to create a user mailbox upon creation of a new user account. To create a user mailbox for an existing user account, use the Exchange Tasks command on that account. For details, see Steps for performing Exchange tasks on a user account.

NOTE: Mailboxes can be created only for Users, enabling mailbox for a Contact is not allowed.

To create a new user mailbox

  1. In the console tree, locate and select the folder in which you want to add the user account.
  2. Right-click the folder, point to New and then click User.
  3. Follow the wizard pages to specify properties of the new user account, such as the user first name, last name, full name, display name, logon name, pre-Windows 2000 logon name, and password.
  4. When prompted for the user alias and mailbox location, accept or change the default alias setting, and select the mailbox database to hold the mailbox data. Optionally, specify a retention policy, Exchange ActiveSync mailbox policy, or address book policy for this mailbox.
  5. Click Finish on the completion page of the wizard.

NOTE: The behavior of the wizard pages may vary depending on the configuration of Active Roles policies. To determine whether a given item on a page is under the control of a certain policy, observe the text label next to the item: the underlined text label indicates that some policy restrictions are in effect. Click underlined text labels to examine the policies that govern the behavior of the wizard pages.

Steps for creating a room or equipment Mailbox

This section provides instructions on how to create a room or equipment mailbox along with a new disabled user account that will be associated with the mailbox. To create a room or equipment mailbox associated with an existing disabled user account, use the Exchange Tasks command on that account. For details, see Steps for performing Exchange tasks on a user account.

To create a new room or equipment mailbox

  1. In the console tree, locate and select the folder in which you want to add the user account.
  2. Right-click the folder, point to New and then click one of the following:
    • Click Room Mailbox to create a room mailbox.
    • Click Equipment Mailbox to create an equipment mailbox.
  3. Follow the wizard pages to specify properties of the new user account, such as the user first name, last name, full name, display name, logon name, pre-Windows 2000 logon name, and password.
  4. When prompted for the user alias and mailbox location, accept or change the default alias setting, and select the mailbox database to hold the mailbox data. Optionally, specify a retention policy, Exchange ActiveSync mailbox policy, or address book policy for this mailbox.
  5. When prompted for the resource mailbox settings, specify the resource capacity and select the resource custom properties to add to the mailbox.

    These settings are optional. After the mailbox has been created, you can view or change these settings on the Resource Information tab in the Properties dialog box for the user account associated with the mailbox.

  1. Click Finish on the completion page of the wizard.

Steps for creating a linked mailbox

This section provides instructions on how to create a linked mailbox along with a new disabled user account that will be associated with the mailbox. To create a linked mailbox associated with an existing disabled user account, use the Exchange Tasks command on that account. For details, see Steps for performing Exchange tasks on a user account.

To create a new linked mailbox

  1. In the console tree, locate and select the folder in which you want to add the user account.
  2. Right-click the folder, point to New and then click Linked Mailbox.
  3. Follow the wizard pages to specify properties of the new user account, such as the user first name, last name, full name, display name, logon name, pre-Windows 2000 logon name, and password.
  4. When prompted for the user alias and mailbox location, accept or change the default alias setting, and select the mailbox database to hold the mailbox data. Optionally, specify a retention policy, Exchange ActiveSync mailbox policy, or address book policy for this mailbox.
  5. When prompted for the linked master account, click Browse and select the user from a trusted forest or domain to which you want to assign the mailbox.

    After the mailbox has been created, you can view or change this setting on the Master Account tab in the Properties dialog box for the user account associated with the mailbox.

  1. Click Finish on the completion page of the wizard.

Steps for creating a shared mailbox

This section provides instructions on how to create a shared mailbox along with a new disabled user account that will be associated with the mailbox. To create a shared mailbox associated with an existing disabled user account, use the Exchange Tasks command on that account. For details, see Steps for performing Exchange tasks on a user account.

To create a new shared mailbox

  1. In the console tree, locate and select the folder in which you want to add the user account.
  2. Right-click the folder, point to New and then click Shared Mailbox.
  3. Follow the wizard pages to specify properties of the new user account, such as the user first name, last name, full name, display name, logon name, pre-Windows 2000 logon name, and password.
  4. When prompted for the user alias and mailbox location, accept or change the default alias setting, and select the mailbox database to hold the mailbox data. Optionally, specify a retention policy, Exchange ActiveSync mailbox policy, or address book policy for this mailbox.
  5. When prompted to specify the users who will have full access to the shared mailbox, click the Add button and then select the users you want.

    This setting is optional. After the mailbox has been created, you can add or remove mailbox users on the Mailbox Sharing tab in the Properties dialog box for the user account associated with the mailbox.

  1. Click Finish on the completion page of the wizard.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级