Chat now with support
Chat with Support

Identity Manager 8.1.4 - Administration Guide for Connecting to SAP R/3

Managing SAP R/3 environments Setting up SAP R/3 synchronization Basic data for managing an SAP R/3 environment Basic data for user account administration SAP systems SAP clients SAP user accounts SAP groups, SAP roles, and SAP profiles SAP products Providing system measurement data Reports about SAP systems Configuration parameters for managing an SAP R/3 environment Default project templates for synchronizing an SAP R/3 environment Referenced SAP R/3 table and BAPI calls Example of a schema extension file

Locking and unlocking SAP user accounts

The way that user accounts are managed determines how you lock them. User accounts that are not linked to an employee, can be locked with the Lock user account task.

To lock a user account

  1. Select the SAP R/3 | User accounts category.
  2. Select the user account in the result list.
  3. Select the Lock user account task.
  4. Confirm the prompt with OK.

    This generates a process that publishes the change in the target system. The User account locked option is enabled as soon as the process is successfully completed.

If the user account is linked to an employee, the user account is unlocked when a new central password is set for the employee. This behavior is controlled by the TargetSystem | SAPR3 | Accounts | UnlockByCentralPassword configuration parameter. For detailed information about an employee’s central password, see One Identity Manager Identity Management Base Module Administration Guide.

To unlock a user account manually

  1. Select the SAP R/3 | User accounts category.
  2. Select the SAP user account in the result list.
  3. Select the Unlock user account task.
  4. Confirm the prompt with OK.

    This generates a process that publishes the change in the target system. The User account locked option is disabled as soon as the process is successfully completed.

Detailed information about this topic

Assigning extended properties

Extended properties are meta objects, such as operating codes, cost codes, or cost accounting areas that cannot be mapped directly in One Identity Manager.

To specify extended properties for a user account

  1. Select the SAP R/3 | User accounts category.
  2. Select the user account in the result list.
  3. Select the Assign extended properties task.
  4. In the Add assignments pane, assign extended properties.

    - OR -

    In the Remove assignments pane, remove extended properties.

  5. Save the changes.
Detailed information about this topic
  • One Identity Manager Identity Management Base Module Administration Guide

Renaming SAP user accounts

You can rename user accounts by deleting them and recreating them under a different name. In this case, existing assignments are transferred to the new user account.

NOTE: User accounts with the Full managed manage level cannot be renamed.

To rename a user account

  1. In the Manager, select the SAP R/3 | User accounts category.
  2. Select the user account in the result list.
  3. Select the Change master data task.

  4. Select the Rename SAP user account task.
  5. Enter the new name of the user account and the initial password.
  6. Click OK.

    This generates a process that publishes these changes to the target system.

Related topics

Automatic assignment of employees to SAP user accounts

Table 54: Configuration parameters for automatic employee assignment
Configuration parameter Meaning
TargetSystem | SAPR3 | PersonAutoFullSync

This configuration parameter specifies the mode for automatic employee assignment for user accounts added to or updated in the database through synchronization.

TargetSystem | SAPR3 | PersonAutoDefault

This configuration parameter specifies the mode for automatic employee assignment for user accounts added to the database outside synchronization.

TargetSystem | SAPR3 | PersonExcludeList

List of all user accounts for which automatic employee assignment should not take place. Names are listed in a pipe (|) delimited list that is handled as a regular search pattern.

Example:

SAP*|SAPCPIC|SAPJSF|DDIC|J2EE_ADMIN|J2EE_GUEST

TargetSystem | SAPR3 | PersonAutoDisabledAccounts

This configuration parameter specifies whether employees are automatically assigned to disabled user accounts. User accounts do not obtain an account definition.

When you add a user account, an existing employee can be assigned automatically or added if necessary. In the process, the employee master data is created on the basis of existing user account master data. This mechanism can be triggered after a new user account is created either manually or through synchronization. Define criteria for finding employees to apply to automatic employee assignment. If a user account is linked to an employee through the current mode, the user account is given, through an internal process, the default manage level of the account definition entered in the user account's target system. You can customize user account properties depending on how the behavior of the manage level is defined.

If you run this procedure during working hours, automatic assignment of employees to user accounts takes place from that moment onwards. If you disable the procedure again later, the changes only affect user accounts added or updated after this point in time. Existing employee assignments to user accounts remain intact.

NOTE: It is not recommended to assign employees using automatic employee assignment in the case of administrative user accounts. Use Change master data to assign employees to administrative user accounts for the respective user account.

Run the following tasks to assign employees automatically.

  • If you want employees to be assigned during the synchronization of user accounts, in the Designer, set the "TargetSystem | SAPR3 | PersonAutoFullsync" configuration parameter and select the mode.
  • If you want employees to be assigned outside synchronization, in the Designer, set the "TargetSystem | SAPR3 | PersonAutoDefault" configuration parameter and select the required mode.
  • In the "TargetSystem | SAPR3 | PersonExcludeList" configuration parameter, specify the user accounts that must not be assigned automatically to employees.

    Example:

    SAP*|SAPCPIC|SAPJSF|DDIC|J2EE_ADMIN|J2EE_GUEST

  • Use the "TargetSystem | SAPR3 | PersonAutoDisabledAccounts" configuration parameter to specify whether employees can be automatically assigned to disabled user accounts. User accounts do not obtain an account definition.
  • Assign an account definition to the client. Ensure that the manage level to be used is entered as the default manage level.
  • Define the search criteria for employee assignment in the client.

NOTE:

The following applies for synchronization:

  • Automatic employee assignment takes effect if user accounts are added or updated.

The following applies outside synchronization:

  • Automatic employee assignment takes effect if user accounts are added.

NOTE:

Following a synchronization, employees are automatically created for the user accounts in the default installation. If an account definition for the client is not yet known at the time of synchronization, user accounts are linked with employees. However, account definitions are not assigned. The user accounts are therefore in a Linked state.

To manage the user accounts using account definitions, assign an account definition and a manage level to these user accounts.

To select user accounts through account definitions

  1. Create an account definition.
  2. Assign an account definition to the client.
  3. Assign a user account in the Linked state to the account definition. The account definition's default manage level is applied to the user account.
    1. In the Manager, select the SAP R/3 | User accounts | Linked but not configured | <Client> category.
    2. Select the Assign account definition to linked accounts task.
    3. In the Account definition menu, select the account definition.

    4. Select the user accounts that contain the account definition.

    5. Save the changes.
Detailed information about this topic
  • One Identity Manager Target System Base Module Administration Guide
Related topics
Related Documents

The document was helpful.

Select Rating

I easily found the information I needed.

Select Rating