Compliance – Cost center (page description)
To open the Compliance - Cost Center page go to Responsibilities > Governance Administration > Cost Centers > Edit > Compliance.
On the Compliance – Cost center page, you can see the rule violations caused by this cost center (see Displaying cost center rule violations).
The following table gives an overview of the different content on the Compliance – Cost center page.
Table 890: Columns
|
Entitlement |
Shows the entitlement that caused the rule violation. |
|
Rule |
Shows the rule that was violated. |
|
Risk index |
Shows the severity of the rule violation (meaning the calculated risk index). The higher this value is, the higher the risk that this rule violation poses. |
|
Risk index (reduced) |
Shows the risk index taking mitigating controls into account. A rule’s risk index can be reduced by a significance amount after mitigating controls have been applied.
Mitigating controls are processes that exist outside the One Identity Manager solution and that reduce the risk of violation. For more information, see Compliance – Governance Administration. |
TIP: On the following tabs, you can show other useful information about each rule violation in the pane. To do this, click the corresponding entry in the list.
TIP: You can show less data by using the column filters. For more information, see Filtering.
Attestation – Cost center (page description)
To open the Attestation - Cost Center page go to Responsibilities > Governance Administration > Organization > Edit > Attestation.
On the Attestation - Cost Center page you can:
The following tables give you an overview of the various features and contents of the Attestation – Cost Center page.
Table 892: Controls in the attestation case's details pane
|
Actions > Send a reminder mail |
Use this action to display all identities that can make approval decisions about the attestation case Then you can send reminder emails to these identities (see Sending reminders about cost center pending attestation cases). |
|
Show details |
You can use this button to display details about all the objects that are included in this attestation case (see . |
Table 893: Columns
|
Display name |
Shows the name of the object included in the attestation case. |
|
Attestation policy |
Shows the name of the attestation policy in use. |
|
State |
Shows the current status of the attestation case.
The following status' are possible:
-
Pending: The attestation case is not closed yet and must still be approved.
-
Approved: The attestation case was approved. In the details pane, on the Workflow tab, you can see why the attestation case was granted approval.
-
Denied: The attestation case was denied. In the details pane, on the Workflow tab, you can see why the attestation case was denied approval. |
|
New |
Shows whether the attestation case is new. New cases have not been granted approval yet but might have been denied approval before. |
|
Due date |
Shows by when the attestation case must be completed. |
|
Risk index |
Show the attestation case's risk index. |
TIP: You can show less data by using the column filters. For more information, see Filtering.
Risk – Cost center (page description)
To open the Risk – Cost center page go to Responsibilities > Governance Administration > Organization > Edit > Risk.
On the Risk – Cost center page, you can:
The risk index is calculated from the sum of all attribute-based values and the maximum of all assignment-based values.
The following tables give you an overview of the various features and content on the Risk – Cost center page.
Table 894: Controls
|
View risk functions |
Use this button to show the attributes and assignments that contribute to the calculated risk index. |
Table 895: Columns
|
Risk index |
Shows which property/assignment affects the risk index. |
|
Risk |
|
|
Weighting/change value |
Shows, depending on the type of calculation, the value used to weigh the determined risk index in the overall calculation or the value used to alter the risk index respectively. |
History – Cost center (page description)
To open the History - Cost Center page go to Responsibilities > Governance Administration > Organization > Edit > History.
On the History – Cost center page, you can see all the changes made to the cost center (see Cost center history).
NOTE: Which changes are shown depends on your system's configuration.
The information is divided out on to three tabs:
-
Events: Shows all events relating to the cost center, either on a timeline or in a table.
TIP: To navigate along the timeline, click in the pane and move the mouse left or right whilst holding down the left button.
To zoom in or out, turn the mouse wheel.
-
Status overview: Shows you an overview of all assignments. It also shows how long each change was valid for. Use the status overview to track when changes were made and by whom. This way, you not only see the initial and current status but you also see all the steps in between.
-
Status comparison: You can select a date and display all the changes made from then until now. You can also show what the value of the property was at the selected point in time and what the value is now.
The following tables give you an overview of the different functions and content on the History – Cost center page.
Table 896: Controls
|
Events tab |
|
Filter by |
Use this function to filter the changes by a specific criteria. For example, you can just display changes from a certain user.
TIP: To remove the filter again, click  (Reset filter) next to the corresponding filter. |
|
Switch to table view |
Use this button to display the changes in table form. |
|
Switch to timeline view |
Use this button to display the changes as a timeline. |
|
Status comparison tab |
|
Time and date picker |
Select from which point on you want to see the changes. |
|
Display changed values only |
Disable this check box if you also want to see properties that have not changed since they were created. |
Table 897: Controls in the details pane of a change
|
Compare |
Opens the Status comparison tab.
Use this button to show all the changes that were made from the selected point in time until now. You can also show what the value of the property was at the selected point in time and what the value is now. |
Table 898: Columns
|
Events tab (table view) |
|
Change type |
Shows the type of change. |
|
Property |
Shows the name of the property that was changed. |
|
Display |
Shows the value that was changed. For example, the name of a department. |
|
Date |
Shows the date the change was made. |
|
User |
Shows the user that made the change. |
|
Status overview tab |
|
Display |
Shows the type of change. |
|
Property |
Shows the name of the property that was changed. |
|
Value |
Shows the value that was changed. For example, the name of a department. |
|
Run started |
Shows when the change was made. |
|
End |
Shows for how long the changed value applied or whether it is currently in use. |
|
Status comparison tab |
|
Modified |
Show whether the change took place or not. |
|
Change type |
Shows the type of change. |
|
Object type |
Show the type of object involved in the change. |
|
Property |
Show the name of the object that was changed. |
|
Historical value |
Shows the value before the change was made. |
|
Current value |
Shows the value that is currently in use. |
TIP: You can show less data by using the column filters. For more information, see Filtering.
