Password Profiles
Use Password Profiles to define the profile configuration settings, including account password rules and password check and change schedules, which can then be used in profile definitions.
Navigate to Asset Management > Profiles > Password Profiles.
Table 154: Profile settings
| Account Password Rules |
Where you define the complexity rules used by Safeguard for Privileged Passwords when constructing new passwords during an automatic account password change |
| Change Password |
Where you define the rules Safeguard for Privileged Passwords uses to reset account passwords |
| Check Password |
Where you define the rules Safeguard for Privileged Passwords uses to verify account passwords |
|
Password sync groups |
Where you define the password sync groups and associated accounts so Safeguard for Privileged Passwords can synchronize passwords across accounts |
Check Password
Check password settings are the rules Safeguard for Privileged Passwords uses to verify account passwords.
Navigate to Asset Management > Profiles > View Password Profile Components > Check Password.
The Check Password pane displays the following about the listed check password setting rules.
Table 155: Check Password: Properties
| Name |
The name of the check password rule. |
| Partition |
The partition that uses the rule. |
| Description |
Information about the rule. |
| Schedule |
Displays the selected rule's schedule. |
Use these toolbar buttons to manage the check password setting rules.
Adding check password settings
It is the responsibility of the Asset Administrator or the partition's delegated administrator to define the rules Safeguard for Privileged Passwords uses to verify account passwords.
Navigate to Asset Management > Profiles > View Password Profile Components > Check Password.
To add a password validation schedule
- Click
Add to open the Check Password Settings dialog.
- Enter a Name of up to 50 characters for the rule.
- Enter a Description of up to 255 characters for the rule.
- Select the partition using the browse button.
-
Optionally, complete either of these settings:
- Open the Schedule tab and choose an interval.
-
In the Schedule dialog, select Run Every to run the job along per the run details you enter. (If you deselect Run Every, the schedule details are lost.)
-
Configure the following.
To specify the frequency without start and end times, select from the following controls. If you want to specify start and end times, go to the Use Time Window selection in this section.
Enter a frequency for Run Every. Then, select a time frame:
- Minutes: The job runs per the frequency of minutes you specify. For example, Every 30 Minutes runs the job every half hour over a 24-hour period. It is recommended you do not use the frequency of minutes except in unusual situations, such as testing.
-
Hours: The job runs per the minute setting you specify. For example, if it is 9 a.m. and you want to run the job every two hours at 15 minutes past the hour starting at 9:15 a.m., select Runs Every 2 Hours @ 15 minutes after the hour.
-
Days: The job runs on the frequency of days and the time you enter.
For example, Every 2 Days Starting @ 11:59:00 PM runs the job every other evening just before midnight.
-
Weeks The job runs per the frequency of weeks at the time and on the days you specify.
For example, Every 2 Weeks Starting @ 5:00:00 AM and Repeat on these days with MON, WED, FRI selected runs the job every other week at 5 a.m. on Monday, Wednesday, and Friday.
-
Months: The job runs on the frequency of months at the time and on the day you specify.
For example, If you select Every 2 Months Starting @ 1:00:00 AM along with First Saturday of the month, the job will run at 1 a.m. on the first Saturday of every other month.
-
Select Use Time Windows if you want to enter the Start and End time. You can click Add or 
Remove to control multiple time restrictions. Each time window must be at least one minute apart and not overlap.
For example, for a job to run every ten minutes every day from 10 p.m. to 2 a.m., enter these values:
Enter Every 10 Minutes and Use Time Windows:
If you have selected Days, Weeks, or Months, you will be able to select the number of times for the job to Repeat in the time window you enter.
For a job to run two times every other day at 10:30 am between the hours of 4 a.m. and 8 p.m., enter these values:
For days, enter Every 2 Days and set the Use Time Windows as Start 4:00:00 AM and End 8:00:00 PM and Repeat 2.
- (UTC) Coordinated Universal Time is the default time zone. Select a new time zone, if desired.
If the scheduler is unable to complete a task within the scheduled interval, when it finishes execution of the task, it is rescheduled for the next immediate interval.
Change Password
Change password settings are the rules Safeguard for Privileged Passwords uses to reset account passwords.
Navigate to Asset Management > Profiles > View Password Profile Components > Change Password.
The Change Password pane displays the following about the listed change password setting rules.
Table 157: Change Password: Properties
| Name |
The name of the rule. |
| Partition |
The partition that uses the rule. |
| Description |
Information about the rule. |
| Schedule |
Displays the selected rule's schedule. |
Use these toolbar buttons to manage the change password setting rules.
Delete
Edit
Refresh 
Search