立即与支持人员聊天
与支持团队交流

Identity Manager 8.2 - Administration Guide for Connecting to Exchange Online

About this guide Managing Exchange Online environments Synchronizing a Exchange Online environment
Setting up Exchange Online synchronization Customizing the synchronization configuration Running synchronization Tasks following synchronization Troubleshooting Ignoring data error in synchronization
Basic data for managing an Exchange Online environment Exchange Online organization configuration Exchange Online mailboxes Exchange Online mail users Exchange Online mail contacts Exchange Online mail-enabled distribution groups
Creating Exchange Online mail-enabled distribution groups Editing main data for Exchange Online mail-enabled distribution groups Main data for Exchange Online mail-enabled distribution groups Receive restrictions for Exchange Online mail-enabled distribution groups Customizing send permissions for Exchange Online mail-enabled distribution groups Specifying moderators for Exchange Online mail-enabled distribution groups Specifying Exchange Online mail-enabled distribution groups Assigning Exchange Online mail-enabled distribution groups to Exchange Online recipients Exchange Online mail-enabled distribution group inheritance based on categories Adding Exchange Online dynamic distribution groups to Exchange Online mail-enabled distribution groups Adding a Exchange Online dynamic distribution group to Exchange Online mail-enabled distribution groups Adding Exchange Online mail-enabled public folder to Exchange Online mail-enabled distribution groups Assigning extended properties to Exchange Online mail-enabled distribution groups Deleting Exchange Online mail-enabled distribution groups
Exchange Online Office 365 groups Exchange Online dynamic distribution groups Exchange Online mail-enabled public folders Reports about Exchange Online objects Configuration parameters for managing an Exchange Online environment Default project template for Exchange Online Editing Exchange Online system objects Exchange Online connector settings

How to configure Exchange Online synchronization

The synchronization project for initial synchronization provides a workflow for initial loading of target system objects (initial synchronization) and one for provisioning object modifications from the One Identity Manager database to the target system (provisioning). To use One Identity Manager as the primary system during synchronization, you also require a workflow with synchronization in the direction of the Target system.

To create a synchronization configuration for synchronizing Exchange Online

  1. In the Synchronization Editor, open the synchronization project.

  2. Check whether the existing mappings can be used to synchronize into the target system. Create new maps if required.

  3. Create a new workflow with the workflow wizard.

    This creates a workflow with Target system as its direction of synchronization.

  4. Create a new start up configuration. Use the new workflow to do this.

  5. Save the changes.
  6. Run a consistency check.

Changing system connection settings of Exchange Online

When you set up synchronization for the first time, the system connection properties are set to default values that you can modify. There are two ways to do this:

  1. Specify a specialized variable set and change the values of the affected variables.

    The default values remain untouched in the default variable set. The variables can be reset to the default values at any time. (Recommended action).

  2. Edit the target system connection with the system connection wizard and change the effected values.

    The system connection wizard supplies additional explanations of the settings. The default values can only be restored under particular conditions.

Detailed information about this topic

Editing connection parameters in the variable set

The connection parameters were saved as variables in the default variable set when synchronization was set up. You can change the values in these variables to suit you requirements and assign the variable set to a start up configuration and a base object. This means that you always have the option to use default values from the default variable set.

NOTE: To guarantee data consistency in the connected target system, ensure that the start-up configuration for synchronization and the base object for provisioning use the same variable set.

To customize connection parameters in a specialized variable set

  1. In the Synchronization Editor, open the synchronization project.

  2. Select the Configuration > Target system category.

  3. Open the Connection parameters view.

    Some connection parameters can be converted to variables here. For other parameters, variables are already created.

  4. Select a parameter and click Convert.

  5. Select the Configuration > Variables category.

    All specialized variable sets are shown in the lower part of the document view.

  6. Select a specialized variable set or click on in the variable set view's toolbar.

    • To rename the variable set, select the variable set and click the variable set view in the toolbar . Enter a name for the variable set.

  7. Select the previously added variable and enter a new value.

  8. Select the Configuration > Start up configurations category.

  9. Select a start up configuration and click Edit.

  10. Select the General tab.

  11. Select the specialized variable set in the Variable set menu.

  12. Select the Configuration > Base objects category.

  13. Select the base object and click .

    - OR -

    To add a new base object, click .

  14. Select the specialized variable set in the Variable set menu.

  15. Save the changes.

For detailed information about using variables and variable sets, or restoring default values and adding base objects, see the One Identity Manager Target System Synchronization Reference Guide.

Related topics

Editing target system connection properties

You can also use the system connection wizard to change the connection parameters. If variables are defined for the settings, the changes are transferred to the active variable set.

NOTE: In the following circumstances, the default values cannot be restored:

  • The connection parameters are not defined as variables.

  • The default variable set is selected as an active variable set.

In both these cases, the system connection wizard overwrites the default values. They cannot be restored at a later time.

To edit connection parameters using the system connection wizard

  1. In the Synchronization Editor, open the synchronization project.

  2. In the toolbar, select the active variable set to be used for the connection to the target system.

    NOTE: If the default variable set is selected, the default values are overwritten and cannot be restored at a later time.

  3. Select the Configuration > Target system category.

  4. Click Edit connection.

    This starts the system connection wizard.

  1. Follow the system connection wizard instructions and change the relevant properties.

  2. Save the changes.
Related topics
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级